Sb-filters Cold Air Intake Kit - Cotton Filter 75-5073 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör für die Luft Sb-filters Cold Air Intake Kit - Cotton Filter 75-5073 herunter. S&B Filters Cold Air Intake Kit - Cotton Filter 75-5073 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 4
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
1. With the ignition switched off and the
parking brake set, disconnect the negative
battery cables on both batteries. (Failure to
disconnect the batteries may result in a
Check Engine Light)
INSTALLATION INSTRUCTIONS
VEHICLE APPLICATION
Year: 2007-10
Make: DODGE
Model: RAM 3500-5500
Chassis Cab Only
Engine: 6.7L Cummins
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.com
4. Loosen the hose clamp at the turbo inlet,
next pinch the spring clamp and slide it up the
steel piping. Then disconnect the silicone
hose from the steel piping and remove spring
clamp.
7. Carefully remove both sensors from the
stock air box and set them aside for now.
2. Disconnect the electrical connection for
the Intake Air Temp. (IAT) Sensor and the
Mass Air Flow (MAF) Sensor then unsnap the
wire loom from the tube. (See the next step
for removal)
5. Remove the mounting nut on the stock air
box.
3. For the MAF sensor, Slide the red locking
tab up then depress the black lever while
disengaging the connector. For the IAT
sensor just depress the grey lever while
disengaging the connector.
6. Lift up and out to remove the stock air
box assembly from the vehicle.
8. Use the supplied 8-32 SS Screws (F)
and Sensor Gasket (E), and install the MAF
sensor into Intake Tube (C). Do not over
tighten.
P/N: 75-5073 / 75-5073D
SEE EXPLODED VIEW ON PAGE 4
1
Locking Tab
Lever
TOOLS REQUIRED
8mm &10mm Wrench & Socket
T-20 Security Torx Wrench (Supplied w/ Kit)
7/16” Wrench and Socket
5/16” Nut Driver or Flat Blade Screwdriver
Phillips Screwdriver, Pliers or Channel locks
NOTES
Kit may not fit with the following
Aftermarket Parts installed:
Remote Start
Body Lift or Lowering Kit
Custom Hood
Intercooler or Turbo upgrades
S&B FILTER MAINTENANCE
Cleanable (KF-1035). If the enclosed filter is Red, it came pre-oiled
from the factory. When serviced, apply (87g) of S&B oil to the main
body of the filter and (17g) to the Power Stack (Top).
Disposable (KF-1035D). If the enclosed filter is White, it is a
disposable filter and should be discarded once it reaches capacity.
This filter (does not require oil). For more info on S&Bʼs disposable
filter, visit www.sbfilters.com.
BEFORE YOU START
Please read the entire product guide before proceeding.
Ensure all components listed on page 4 are present.
If you are missing any of the components, call our customer support at (909) 947-0015.
Do not work on your vehicle while engine is hot.
Make sure the engine is turned off and the vehicle is in Park or the Parking Brake is set.
9. Place the Silicone adapter (B) and both
#64 Hose Clamps (A) onto the Intake tube (C)
as shown. Leave 1.25” between the end of
the silicone and the end of the intake tube.
Tighten the clamp on the intake tube.
1.25”
2010 models: Classic body Only
Seitenansicht 0
1 2 3 4

Inhaltsverzeichnis

Seite 1 - P/N: 75-5073 / 75-5073D

1. With the ignition switched off and the parking brake set, disconnect the negative battery cables on both batteries. (Failure to disconnect the bat

Seite 2

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.comINSTALLATION INSTRUCTIONS (continued)14. Slide t

Seite 3

EMISSIONS STANDARDThe California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smo

Seite 4 - EXPLODED VIEW

ITEMQTY.DESCRIPTIONP/NA2Hose Clamp, #64AI1018-00B1Silicone Adapter, 4.10” x 2.0”AI1029S-00C1Intake TubeAL1162-00D1IAT Sensor GasketAI1302-00E1MAF Sens

Kommentare zu diesen Handbüchern

Keine Kommentare