Sb-filters Cold Air Intake Kit - Cotton Filter 75-5066 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör für die Luft Sb-filters Cold Air Intake Kit - Cotton Filter 75-5066 herunter. S&B Filters Cold Air Intake Kit - Cotton Filter 75-5066 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 4
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
1. With the ignition switched off and the
parking brake set, disconnect the negative
battery cable on the driver’s side.
Installation Instructions
Vehicle Application!
Make: DODGE/ RAM !
Year/Model: 2013 1500,
2009-13 2500/3500!
Engine: 5.7L Hemi V8
15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.com
4. Remove the crank case vent tube from
the air box.
7. From inside the engine compartment,
carefully pull the wiring harness connector out
from the wheel liner. Then remove the wheel
liner from the truck.
2. Disconnect the electrical connection for
the Temp (IAT) Sensor. Note the sensor’s
orientation for the re-install.
5. Remove air box by carefully pulling the air
box up out of the four pins in the air box tray.
Then remove the two bolts mounting the tray
to the frame using 13mm socket.
8. Using 13mm socket, remove the other 2
bolts securing the air box tray. Then remove
the tray from the truck
3. Loosen the hose clamp connecting the
tube to the air box and the clamp attaching
the tube to the throttle body. Then remove
intake tube from the truck.
6. Remove the seven screws securing the
wheel liner using 8mm socket. Then remove
the 3 push pins. S&B has supplied new panel
pins in the event that the OE pins are
damaged during removal.
P/N: 75-5066 / 75-5066D
SEE EXPLODED VIEW ON PAGE 4
1
Tools Required!
8mm, 10mm, 13mm Wrench & Socket!
Pin Removal Tool or Flat Blade Screwdriver"
7/16” Wrench and Socket"
5/16” Nut Driver or Flat Blade Screwdriver"
Phillips Screwdriver
Notes!
Kit may not fit with the following
Aftermarket Parts installed:"
Body Lift or Lowering Kit"
Custom Hood"
Throttle body upgrades
S&B Filter Maintanence!
Cleanable (KF-1056). If the enclosed filter is Red, it came pre-oiled
from the factory. Please visit www.sbfilters.com for the exact oil
amount required after cleaning."
"
Disposable (KF-1056D). If the enclosed filter is White, it is a
disposable filter and should be discarded once it reaches capacity.
This filter (does not require oil). For more info on S&B’s disposable
filter, visit www.sbfilters.com.
Before You Start!
Please read the entire product guide before proceeding."
Ensure all components listed on page 4 are present."
If you are missing any of the components, call our customer
support at (909) 947-0015."
Do not work on your vehicle while engine is hot."
Make sure the engine is turned off and the vehicle is in Park.
9. Insert the supplied Grommet (D) into the
Air Box (M).
CARB Status - Pending!
Product will be submitted to Air Resources
Board for approval shortly."
"
Not Legal for use in CA or other states
adopting CA emissions standards"
See Page 3 for more info.
Seitenansicht 0
1 2 3 4

Inhaltsverzeichnis

Seite 1 - P/N: 75-5066 / 75-5066D

1. With the ignition switched off and the parking brake set, disconnect the negative battery cable on the driver’s side.Installation InstructionsVehi

Seite 2

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.comInstallation Instructions (continued)10. Insert

Seite 3

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbfilters.comInstallation Instructions (continued)25. Reconn

Seite 4 - Exploded View

ITEMQTY.DESCRIPTIONP/NA1Hose Clamp, #56AG1019-00B1Silicone Step CouplerAI1306S-00C1Hose Clamp, #60AG1008-00D2GrommetAI1563-00E1Intake TubeAL1182-00F2H

Kommentare zu diesen Handbüchern

Keine Kommentare