Sb-filters Intake Elbow 6-1007 Bedienungsanleitung PDF herunterladen

8. This kit has 2 long studs (J) and 2 short studs (H), to determine the correct stud length for your

truck, thread each a long and short stud (short threaded end ﬁrst) into the manifold bolt holes farthest

from the valve cover. Measure the height of the stud from the heater grid block upward. Use the

studs that are approximately 1.125” tall.

1. With the ignition switched off and the

parking brake set, disconnect the negative

battery cables on both batteries.

INSTALLATION INSTRUCTIONS

VEHICLE APPLICATION

Year: 1998.5-02

Make: Dodge

Model: Ram 2500, 3500

Engine: 5.9L Cummins Diesel

! 24 Valve only

TOOLS REQUIRED

•

10mm, 13mm, 1/2” Wrench & Socket

•

7/16” Deep Socket

•

3/16”, 4mm, 6mm Hex Drive

•

Torque Wrench (In.lb.)

•

Gasket Remover (Scraper)

•

Vacuum

CAUTION

Use a 1/4 inch drive ratchet. NOTE: All

required torque specs. are called out in Inch

pounds NOT foot pounds!

BEFORE YOU START

•

Please read the entire product guide before proceeding.

•

Ensure all components listed on page 4 are present.

•

If you are missing any of the components, call our customer support at (909) 947-0015.

•

Do not attempt to work on your vehicle while engine is hot.

•

Make sure the engine is turned off and the vehicle is in Park or the Parking Brake is set.

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbﬁlters.com

4. Pull the prong out that secures the wiring

harness to the elbow and push the harness

back away from the elbow.

7. Place the supplied Graphite Gasket (I) on

the manifold under the heater block, make

sure all four bolt holes in the gasket line up

correctly.

2. Loosen the upper hose clamp at the OE

elbow and disconnect the hump hose from

the elbow. Note: Care should be taken not to

let any debris fall into the boost tube.

5. Remove the 4 bolts that secure the elbow

to the manifold and remove the elbow from

the vehicle. Careful not to let any debris fall

into the manifold. Note: If the OE bolt threads

were corroded and rust deposits have fallen

through the bolt holes into the manifold use a

vacuum to clean it out.

3. Remove the bolt that secures the dip

stick tube to the elbow.

6. Remove both gaskets on each side of

the OE heater grid block. A scraper may be

necessary, be careful not to damage the

sealing surface and to not let any debris fall

into the manifold. You may need a vacuum at

this step as well.

P/N: 76-1007

SEE EXPLODED VIEW ON PAGE 4

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - P/N: 76-1007

8. This kit has 2 long studs (J) and 2 short studs (H), to determine the correct stud length for your truck, thread each a long and short stud (short

Seite 2

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbﬁlters.comINSTALLATION INSTRUCTIONS (Continued)9. Remove t

Seite 3

EMISSIONS STANDARDThe California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smo

Seite 4 - EXPLODED VIEW

ITEMQTY.DESCRIPTIONP/NA2Washer, Flat, 5/16”AI1073-00B1Bolt, Hex, 5/16-18x1/2”AI1078-00C2Nut, Hex, Nylock, 8mmAI1401-00D4Washer, Flat, 8mmAI1402-00E2Ca

Seite 5

15461 Slover Ave., Fontana, CA 92337 - Phone: (909) 947-0015 - Fax: (909) 947-0603 - www.sbﬁlters.comINSTALLATION INSTRUCTIONS Addendum5P/N: 76-1007Ho

Kommentare zu diesen Handbüchern

Keine Kommentare

Sb-filters Intake Elbow 6-1007 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör für die Luft Sb-filters Intake Elbow 6-1007 herunter. S&amp;B Filters Intake Elbow 6-1007 User Manual [it] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör für die Luft Sb-filters Intake Elbow 6-1007

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör für die Luft Sb-filters Intake Elbow 6-1007 herunter. S&B Filters Intake Elbow 6-1007 User Manual [it] Benutzerhandbuch